Big Horn 18945 #6 screw taper drill. Recommended for most jobs, whether in a drill press or in hand held equipment. Cuts very well in both hard and soft woods. To cut wood and plastics in one operation for the thread and shank of wood screws. Taper Point Drills are made of High Speed Steel to hold their sharp cutting edges longer. Replaces W. L. Fuller # 20100140.
Drill Gauges help you to quickly and accurately identify the sizes of stray drill bits in your workshop. These Gauges can be extremely useful with older, unmarked bits or ones that are too small for markings. Heavy steel Gauge is machined to close tolerance for spot-on accuracy. The bit sizes and decimal equivalents are permanently etched to the face to provide years of dependable use.
These highly accurate, self-centering hinge drilling hinge bits are used for precise drilling of holes for cabinet and door hinges, door butts, striker plates, window pulls and all large and small hardware. Desired depth is achieved by loosening a setscrew, setting the high speed drill bit, and then tightening the setscrew. Bit is Self-centering & accurate. Body has screw top for ease of cleaning & changing bit. Replaceable bits. Bodies are stamped with size. The spring loaded outer guide keeps drill centered for perfect pilot holes. Top unscrews for easy cleaning.
Big Horn 70156 'A' Latch & Strike Template Kit. 1" x 2-1/4" latch template and 1" x 2-1/4" full lip strike template - Replaces Templaco LS-166A.Using your router this template kit will produce the finish mortise on both the door and the jamb. The strike template is for a ”full lip” style strike which is 2-1/4” tall and is mortised completely through the edge of the jamb so it creates a three sided mortise, actual width on the template is 1-7/8" wide. The door edge template finish size is 1” x 2-1/4”. Both templates are attached to the door and the jamb using the built in nail assemblies. Supplied with one Red Plastic Center Locator as shown to locate the templates onto the door and jamb in the proper position.
Big Horn 70131 'A' Latch Template with Center Locator - Finish Size 1-Inch x 2-1/4-Inch Replaces Templaco LT-121A. Center Locator, 1-Inch x 2-1/4-Inch Replaces Templaco 1595A. Center locators will precisely locate the template over the hole bored into the door or jamb. Just insert the locator into the bored hole, place the template over the locator, set the nails to attach the template onto the door or jamb, remove the locator and rout the mortise with your router.
Big Horn 70132 'A' Strike Template with Center Locator - Finish Size 1-Inch x 2-1/4-Inch Replaces Templaco ST-146A.Center Locator, 1-Inch x 2-1/4-Inch Replaces Templaco 1595A. Center locators will precisely locate the template over the hole bored into the door or jamb. Just insert the locator into the bored hole, place the template over the locator, set the nails to attach the template onto the door or jamb, remove the locator and rout the mortise with your router.
Big Horn 70157 'B' Latch & Strike Template Kit.1-1/8" x 2-1/4" Latch Template & 1-1/8" x 2-3/4" 'T' Strike & Dead Bolt Template - Replaces Templaco LS-171B. Use this two template kit with your router to produce the finish mortise on both the door and the jamb. The strike (jamb) template will produce two mortises, the 1-1/8” x 2-3/4” 'T' strike with the red plastic block-off plate removed and the 1-1/8” x 2-3/4” deadbolt strike with the red plastic insert block-off plate installed. The latch template will produce a finish mortise of 1-1/8” x 2-1/4” on the door edge. Each template has two nail assemblies to attach the templates to the jamb and door. Template set is supplied with two red plastic Center Locators used to position the templates on the door and jamb in the proper position.
Big Horn 70134 'B' Strike Template with Center Locator - Finish Size 1-1/8-Inch x 2-3/4-Inch Replaces Templaco ST-151B.Center Locator, 1-1/8-Inch x 2-3/4-Inch Replaces Templaco 1595-B/S. Center locators will precisely locate the template over the hole bored into the door or jamb. Just insert the locator into the bored hole, place the template over the locator, set the nails to attach the template onto the door or jamb, remove the locator and rout the mortise with your router.
